Embedding Accessories
Electron Microscopy Sciences Paraffin TMA Arraymold Kit B, Blue, 1.5 mm diameter, 150 cores per mold Capacity
The Arraymold is the simple tool for laboratories to perform Paraffin tissue microarrays (TMAs) w/ less time while maintaining excellent results. Process up to 150 specimens onto one single slide w/ very little time consuming, minimal technical training. The DVD instruction is accompanying w/ each kit, will step by step guide you to perform through the entire TMAs process. Arraymolds allow pathologist or researcher to view many different samples on the same single slide. Helpful in finding IHC markers for control or quality assurance from hundreds of samples. Staining markers will be more consistent when hundreds of samples are on one slide. Used less costly antibody.Arraymold kit is small enough to be stored in a drawer.Rubber arraymold can be reused many times without losing its flexibility. Generates 1.5 mm diameter sample core, 150 cores per mold. Kit: 10 Disposable 2mm sterile dermal needles, 2 Stylets, 1 Brass Plate, 1 1.5mm reusable rubber Arraymold, DVD.Color: Blue
Electron Microscopy Sciences Peel Away Disposable Embedding Mold Truncated Shape 8 x 8 mm
Peel Away Disposable Embedding Molds are used for plastic or paraffin embedding. No block trimming needed. Inside fingers hold ID slip which becomes embedded in the block for positive permanent identification.
Size: 8 x 8 mm
Leica Biosystems D-Formalizer Powder - Aldehyde Neutralizer for Spent Formalin, 10 x 680 g
D-Formalizer is a powdered aldehyde neutralizer for histology laboratories that treats spent formalin and 4% glutaraldehyde, producing a clear, non-odorous solution suitable for disposal. It simplifies chemical waste handling by neutralizing aldehydes and minimizing solids that can clog drains; one packet is formulated to treat approximately one gallon of used fixative.
- Neutralizes spent formalin and 4% glutaraldehyde
- Produces a clear solution free of solids and aldehyde odor
- Simplifies hazardous waste handling and disposal
- Single-packet dosing treats about one gallon of used fixative
- Powdered form mixes easily for quick treatment
Electron Microscopy Sciences Flat Embedding Mold Flat Embedding Mold Double Ends, 5 mm deep, 14 x 4 mm
A clear silicone rubber with very high tear strength. It can be reused more times than the conventional silicone molds. It is resistant to most epoxy resins and its clear base allows positioning of the specimen lighted from beneath. Flat mold has both ends tapered for embedding in both ends of each casting.
Depth: 5 mm
Size: 14 x 4 mm
Cavities: 21
Electron Microscopy Sciences Molding Cup Tray, 5 mm height
These polyethylene trays are ideal for casting specimen blocks embedded with JB-4 or equivalents and are used with our block holders and chucks shown above.
Size: 6 x 8 mm
Height: 5 mm
Electron Microscopy Sciences Embedding Shelf, size 4 x 8"
This removable shelf can be installed below the opening of the cryostat in the most convenient and location available. The selves can be made in various sizes to accommodate most instruments.
Electron Microscopy Sciences TI Embedding Rings
The most difficult step of cross-sectional thinning is the mechanical preparation of the sample, i.e. cutting a cross section and then embedding it into an appropriately designed ring. We now offer a convenient, specially designed embedding ring for cross-sectional samples.
Using this ring, embedding cross sections is greatly simplified, since the samples do not need to be glued together prior to embedding. In order to fix the sample(s) in the ring, it is deformed mechanically by an appropriate tool at the two points marked by the arrows. This deformation will both hold the sample in the ring and press both sample pieces together before gluing. Ti disc is also offered for embedding bulk samples of brittle material for plan-view TEM investigations. The rings come in 5 sizes-0.6, 0.8 1.0, 1.2, 1.3 mm.
Electron Microscopy Sciences Stainless Steel. Biopsy Insert
A two-part loose fitting stainless steel capsule with welded mesh that fits inside the processing cassettes preventing the loss of small or friable material while allowing interchange of fluids. They fit all process/embedding cassettes such as 70025 and 72025 as well as Uni-Cassettes (62500).
Electron Microscopy Sciences Easy-Molds™ for size 00 Capsules, 8 mm diameter
A newly designed mold which is convenient and offers better embedments. This tray-and-mold in one unit offers a unique specimen block that no other mold can. Each tray contains 2x10 block molds and measures 87x66 mm. Size 8mm diameter corresponds to capsule size "00" and forms a block face of 3mm.